Vehicles
100 not categorized PORSCHE 924 EMBLECan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.FVD123011 These actuators are assembled with yellow springs for boost levels in the 9-15 psi (0.62-1.03 bar) range. Additional springs are available for tuning to custom boost level. These replacement actuators are supplied complete with brackets ready to install. General Fitment911 TURBO/GT2 2001-05
From $524.70
Make a selection POR1700 Techna fit's d.o.t. Certified, high performance, brake line kits are made to fit all makes and models of cars.our brake lines are made of the finest ptfe hose and permanently crimped-on zinc plated steel fittings. Our hose is made with an extruded ptfe core and a stainless steel wire braided cover. They reduce volumetric expansion giving you the reliability and safety you demand. Overtime and under continuous use, OEM rubber lines can swell and expand, exposing the driver to brake fade. The rubber cover is also vulnerable to attacks from the ozone layer rubber which causes it to deteriorate. In extreme applications (auto x, racing, hard driving) rubber hoses might be susceptible to flying debris. Stainless ste...(choose a part on the right to read more) General Fitment911 1998-05
$121.50
Make a selection FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD116838 4 puck sintered metallic material which has a higher thermal capacity than organic friction material. Rigid center hub. Aggressive start performance. Hub length 1.18 inches (30mm) outside 1.21 (30.8mm) 240mm weighs: 2.2 lbs (1.01 kg) direct replacement for the oe clutch disc. Made in Germany by zf sachs race engineering. Please note: due the aggressive start performance of the sintered disc, we do not recommend this disc for street cars. We also recommend that you purchase a sport / racing pressure plate in conjunction with this disc. The sachs racing clutch discs with sintered metal plates have a higher friction coefficient than plates with organic friction material. That allows for higher transmittable torque...(choose a part on the right to read more) General Fitment911 GT3 2003-05911 1994-98 968 1992-95 911 1989-94 944 1982-85 944 1985-88
From $477.94
Make a selection FVD34101702ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection POR1200 Techna fit's d.o.t. Certified, high performance, brake line kits are made to fit all makes and models of cars.our brake lines are made of the finest ptfe hose and permanently crimped-on zinc plated steel fittings. Our hose is made with an extruded ptfe core and a stainless steel wire braided cover. They reduce volumetric expansion giving you the reliability and safety you demand. Overtime and under continuous use, OEM rubber lines can swell and expand, exposing the driver to brake fade. The rubber cover is also vulnerable to attacks from the ozone layer rubber which causes it to deteriorate. In extreme applications (auto x, racing, hard driving) rubber hoses might be susceptible to flying debris. Stainless ste...(choose a part on the right to read more) General Fitment928 1983-86
$121.50
Make a selection FVD34101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD34101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection MAP09028016 The Porsche flat six boxer engine and the cars it powers are legendary. with this kit you can assemble a model of a 1966 2.0 litre flat six engine in around three hours. Discover the fascinating world of automotive engineering with the whole family
From $195.00
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD559213 Includes the later model (series iii from 2009) water cooled crest, gasket and emblem securing nuts. Size: 67 mm x 51 mm sold individually. 1 is necessary per car.
$226.72
Make a selection FVD559212 Includes the later model (series ii from 996) water cooled crest, gasket and emblem securing nuts. Size: 67 mm x 51 mm sold individually. 1 is necessary per car.
$214.78
Make a selection PCG04320204 356 car cover - light gray with original Porsche emblem and lettering. 100% polyesterm air permeable, anti-static, flame-resistant, & is washable at 30c degrees. View/Change Diagram
From $437.95
Make a selection FVD34101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. The reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD341999r. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform you immediately. General Fitment911 1989-94
From $418.00
Make a selection POR1020 Techna fit's d.o.t. Certified, high performance, brake line kits are made to fit all makes and models of cars.our brake lines are made of the finest ptfe hose and permanently crimped-on zinc plated steel fittings. Our hose is made with an extruded ptfe core and a stainless steel wire braided cover. They reduce volumetric expansion giving you the reliability and safety you demand. Overtime and under continuous use, OEM rubber lines can swell and expand, exposing the driver to brake fade. The rubber cover is also vulnerable to attacks from the ozone layer rubber which causes it to deteriorate. In extreme applications (auto x, racing, hard driving) rubber hoses might be susceptible to flying debris. Stainless ste...(choose a part on the right to read more) General Fitment911 1989-94
$121.50
Make a selection FVD33300905ATK Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this does not fit cars with the g50 transmission.
$312.40
Make a selection POR600 Techna fit's d.o.t. Certified, high performance, brake line kits are made to fit all makes and models of cars.our brake lines are made of the finest ptfe hose and permanently crimped-on zinc plated steel fittings. Our hose is made with an extruded ptfe core and a stainless steel wire braided cover. They reduce volumetric expansion giving you the reliability and safety you demand. Overtime and under continuous use, OEM rubber lines can swell and expand, exposing the driver to brake fade. The rubber cover is also vulnerable to attacks from the ozone layer rubber which causes it to deteriorate. In extreme applications (auto x, racing, hard driving) rubber hoses might be susceptible to flying debris. Stainless ste...(choose a part on the right to read more) General Fitment944 1985-88
$121.50
Make a selection POR550 Techna fit's d.o.t. Certified, high performance, brake line kits are made to fit all makes and models of cars.our brake lines are made of the finest ptfe hose and permanently crimped-on zinc plated steel fittings. Our hose is made with an extruded ptfe core and a stainless steel wire braided cover. They reduce volumetric expansion giving you the reliability and safety you demand. Overtime and under continuous use, OEM rubber lines can swell and expand, exposing the driver to brake fade. The rubber cover is also vulnerable to attacks from the ozone layer rubber which causes it to deteriorate. In extreme applications (auto x, racing, hard driving) rubber hoses might be susceptible to flying debris. Stainless ste...(choose a part on the right to read more) General Fitment944 1985-88
$121.50
Make a selection POR625 Techna fit's d.o.t. Certified, high performance, brake line kits are made to fit all makes and models of cars.our brake lines are made of the finest ptfe hose and permanently crimped-on zinc plated steel fittings. Our hose is made with an extruded ptfe core and a stainless steel wire braided cover. They reduce volumetric expansion giving you the reliability and safety you demand. Overtime and under continuous use, OEM rubber lines can swell and expand, exposing the driver to brake fade. The rubber cover is also vulnerable to attacks from the ozone layer rubber which causes it to deteriorate. In extreme applications (auto x, racing, hard driving) rubber hoses might be susceptible to flying debris. Stainless ste...(choose a part on the right to read more) General Fitment944 1985-88
$121.50
Make a selection VEILPREM4509PANAMERA Premier4509 complete kit is constructed with frp & carbon fiber. The veilside craftsmanship is top notch with only the highest quality materials available. General FitmentPANAMERA 2010-14
$37,577.25
Make a selection POR900 Techna fit's d.o.t. Certified, high performance, brake line kits are made to fit all makes and models of cars.our brake lines are made of the finest ptfe hose and permanently crimped-on zinc plated steel fittings. Our hose is made with an extruded ptfe core and a stainless steel wire braided cover. They reduce volumetric expansion giving you the reliability and safety you demand. Overtime and under continuous use, OEM rubber lines can swell and expand, exposing the driver to brake fade. The rubber cover is also vulnerable to attacks from the ozone layer rubber which causes it to deteriorate. In extreme applications (auto x, racing, hard driving) rubber hoses might be susceptible to flying debris. Stainless ste...(choose a part on the right to read more) General Fitment911 1965-69
$121.50
Make a selection PT911 Permatune has long been a favorite alternative to the outrageously priced Bosch electronic ignition control unit. Meticulously assembled by fellow americans in texas, the permatune outperforms the Bosch unit and at a much lower price. Installation is a direct plug-in. Get the spark back in your life today! Output: 350 volts, 3 amps. General Fitment911 1970-73911 1974-77 914 1970-76
$625.50
Make a selection POR650 Techna fit's d.o.t. Certified, high performance, brake line kits are made to fit all makes and models of cars.our brake lines are made of the finest ptfe hose and permanently crimped-on zinc plated steel fittings. Our hose is made with an extruded ptfe core and a stainless steel wire braided cover. They reduce volumetric expansion giving you the reliability and safety you demand. Overtime and under continuous use, OEM rubber lines can swell and expand, exposing the driver to brake fade. The rubber cover is also vulnerable to attacks from the ozone layer rubber which causes it to deteriorate. In extreme applications (auto x, racing, hard driving) rubber hoses might be susceptible to flying debris. Stainless ste...(choose a part on the right to read more) General Fitment944 1989-91
$121.50
Make a selection PT930 Permatune has long been a favorite alternative to the outrageously priced Bosch electronic ignition control unit. Meticulously assembled in texas, the permatune outperforms the original unit and at a much lower price. Installation is a direct plug-in. Get the spark back in your life today! Output: 350 volts, 3 amps. Special order and built on request. Please allow an extra ten days for delivery. General Fitment930 1975-77
$575.00
Make a selection T55110229 Distributor drive tool. Allows for the removal & installation of the distributor drive while the engine is assembled. General Fitment356 1950-59356 1960-65
$83.11
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |